哈尔滨积家 维修-新闻资讯

积家(JAEGER-LECOULTRE)售后服务中心客服电话：400-875-1181(请您提前预约避免工作人员因国家法定假日调整上下班时间和维修人员过多而给您带来不便!)

　　【积家：手表售后维修中心门店图】

　　【图为积家：手表抛光工作台】

　　【上图为积家：手表做真空、压缩、冷凝及防水测试的设备】

　　在手表机芯零件重最“娇气”的，当属于摆轮和游丝。摆轮是因为它的轴椎非常的细，大约只有 0.10mm，摆轮在手表内做高速震荡旋转，摆轮的整个质量都要靠它来支撑。现在的手表都装有防震器，可以有效的保护摆轮轴椎在强烈震动冲击下不被破坏。

　　游丝(Hair spring) 实际上是个微小的螺旋状的弹簧，其形状被称之为“阿基米德螺旋线”。大约盘了10圈多点，用一种成分极为复杂的镍基资料制成。它是维持摆轮的机械震荡中最重要的零件，它的安装，调校，形状，在快慢夹中的间隙和荡匡是决定手表走时精度的最关键部分。?

in the watch movement parts most squeamish, when the balance wheel and spring. Is it because the balance axis is very small, only about 0.10mm, the balance wheel in a watch in high speed shock wheel rotation, the quality of the whole depend on it to support. Now the watches are equipped with shock absorbers, can effectively protect the vertebral axis balance was not damaged in strong vibration shock.

(Hair spring) hairspring is actually a small spiral spring, its shape is called "Archimedes spiral". About 10 laps, with a very complex composition of nickel based materials. It is the most important to maintain the balance of the mechanical shock in its parts, installation, adjustment, shape, speed and the gap in the folder on the marina is the most critical part decided to watch precision.

　　游丝的刚性，间距和圈数，与手表的震荡频率和机芯大小有关。一般讲，频率低的或是积家表，则游丝比较“软”小，反之，频率越高，游丝也就越“硬”。

　　早期的“慢摆”手表(18000次/时)，手表在被摔碰了以后，游丝最容易出现“挂圈”的现象。就是游丝的内圈被挂在游丝外桩或快慢夹上面了。通常表现为，手表停走或走时极快。

　　现在的手表，频率多为 28800/时的震频，游丝比较硬，间距也小，手表在被摔了以后，游丝容易出现的问题是变形。所谓变形，是指游丝发生水平和垂直的便宜，这样游丝就变的不平或不圆了。

　　其中，以水平变形为最多，游丝不同心了。还有，它可能会在工作游荡的过程中，蹭到游丝外桩上。其故障表现为，手表容易停走，走时变快，具体快的程度要看游丝解除到外桩上贴紧的程度了，严重的，可以一天快到2小时。

　　很多被维修过的手表(特别是ETA机芯的)，发现游丝无一例外都水平位移和变形，而且，都是游丝的第二圈蹭到了游丝的外桩上面。在修理上，需要用镊子给游丝坐个精心的矫正，务必保证同心，保证它的螺距，平和圆。

　　如果发现手表不慎被摔了以后，出现走时停和伴随时变的极快现象，那多半回是游丝变形了。当然，还有可能别的部件也同时发生故障。

spring rigidity, spacing and the number of rings, and watch on the oscillation frequency and core size. Generally speaking, the low frequency or brand word , then hairspring more "soft" small, on the other hand, the higher the frequency, it is "hard hairspring".

early "slow pendulum" watch (18000 /), watch after being crash, most likely the "gossamer hanging ring" phenomenon. Is the inner ring is hung above the gossamer clip in the pile or the speed of hairspring. Usually shown as the watch stops or goes fast.

now watch, frequency for earthquake frequency 28800/, gossamer hard spacing is small, the watch after the fall, the deformation problem is prone to spring. The so-called deformation, refers to the occurrence of horizontal and vertical gossamer gossamer becomes cheaper, so uneven or not round.

, the horizontal deformation is the most, not concentric hairspring. Also, it may be in the process of work wandering, rub to pile on the hairspring. The fault is easy to watch, stop and go, go faster, the faster depends on the extent of lifting of the pile with gossamer tight degree, serious, can one day to 2 hours.

many repairs watch (especially ETA movement), and found that the deformation, horizontal displacement and hairspring without exception, are second laps to rub gossamer gossamer pile top. In the repair, need to use tweezers to sit a careful correction of hairspring, make sure that it's pitch, concentric, flat and round.

if accidentally found the watch fell, fast stop and go and appear phenomenon with time varying, the mostly back is gossamer deformation. Of course, there may be other parts of the fault occurs at the same time.

分享到：