合肥积家手表特约维修|维修服务中心|维修环境透明

积家(JAEGER-LECOULTRE)售后服务中心客服电话：400-875-1181(请您提前预约避免工作人员因国家法定假日调整上下班时间和维修人员过多而给您带来不便!)

　　【积家：手表售后维修中心门店图】

　　【图为积家：手表抛光工作台】

　　【上图为积家：手表做真空、压缩、冷凝及防水测试的设备】

　　名牌手表,最需要的是保养,如果不好好保养,损失的不仅是手表,还有钱财,因此首先要做的是手表保养。

　　名表需要细心呵护

　　1.手表的保养

　　手表的使用寿命与佩戴者是否正确使用和保养手表有关,例如佩戴手表洗澡、手表外观肮脏、表带长度不适、使用环境恶劣等,都易导致手表损坏,缩短使用寿命。

　　中高档手表每隔两至三年应做相应的保养,更换防水元件,检测走时性能和机芯功耗,清洗机芯,以及养护外观等,这样的保养服务将有效延长您的手表的使用时间。

　　2.手表的防水性

　　手表的防水依靠表镜、后盖、把头等处的防水胶圈而达到相应的标准。所有防水表均在底盖上打有“WATER RESISTANT”或“WATER PROOF”的英文字样。无防水标记手表仅能防尘,应避免沾水。30米 (3ATM,即3个大气压)防水表,可用于日常梳洗或雨中使用,即水滴只溅在表面上而未有任何水压加于表上。50米防水表可适用于游泳及一般家务,100米防水表可用于游泳和潜水等水下工作。

　　防水胶圈的老化会影响手表的防水性能,所以手表的防水胶圈和把头(内含防水圈)根据使用情况要定期更换。石英表在每次换电池时须同时更换防水元件,以保证防水性能良好。

　　任何防水表都不宜戴着洗热水浴、浴或在温度变化很大的环境中使用。因为防水胶圈受温度影响会热胀冷缩出现空隙并加速老化从而引起进水和表内出现水凝结物,严重的将使机件损坏。

　　3.表带

　　表带分为:陶瓷带、金属带(钨钛合金带、实心钢带、实心铜带、实心粉末冶金钢带、钢片带、钢丝编织带等)、皮带、尼龙编织带等。

　　陶瓷表带有不易磨损、不会过敏、美观等特点。

　　4. 手表的“两防”

　　在国家标准中,防磁和防震性能标准是用“剩余效应”来表示的,剩余效应指的是检测前手表的瞬时日差与检测后手表的瞬时日差之差。

　　防震:当手表从1米高度偶然跌到水平硬木表面时,石英表剩余效应不超过2秒,机械表的剩余效应不超过60秒。

　　防磁:当手表偶然处于强度为4800A/m的磁场中时,石英表剩余效应不超过1.5秒,机械男表(机芯面积大于314平方毫米)剩余效应不超过30秒,机械积家表剩余效应不超过45秒。

　　5.手表除水秘藉

　　不小心表壳内进水了,可用一种叫做硅胶的颗粒状物质与已经积水的手表一起放进一个密闭的容器内,数小时后,取出手表,积水即全部消失。此法简单经济,对表的精度和寿命均无任何损害。已经多次吸水后的硅胶,可在120℃下干燥数小时,吸水能力可再生,还能反复多次使用。

　　6. 手表翻新秘藉

　　手表蒙被划出很多道纹以后,可以在表蒙上先滴一二滴清水,再挤一点牙膏擦涂,就可以把划纹去掉而使表蒙如新了。

　　7.手表保养秘藉

　　(1)戴手表时,手上的汗水对表壳有腐蚀性,全钢表壳由于是镍铬合金,抗腐蚀性能好些,半钢表壳是铜的,长期与汗水接触,容易腐蚀,应经常用软布抹去汗水或垫上塑料表托,以防止其被汗水侵蚀。

　　(2)不要随意打开表后盖,以免尘埃进入机芯影响手表的正常工作。

　　(3)不要将手表放在有樟脑丸的衣柜内,以免表油变质。

　　(4)不要将手表放在收音机、电视机上,以免磁化。

　　(5)长期存放不戴的手表,应每月定期上发条一次,使零件不致长期处于静止状态,以保证表机的运转性能。

brand-name watches, the most needed is maintenance, if not properly maintained, the loss is not only watches, as well as money, so the first thing to do is watch maintenance.

watches need careful care

1 watches maintenance

is the life of the watch and the wearer the proper use and maintenance of watches, such as wearing a watch, watch, watch strap dirty bath length discomfort, bad environment, are likely to cause damage to the watch, shorten the service life.

luxury watches every two to three years should make the corresponding maintenance, replacement of waterproof components, detection performance and power consumption as core, cleaning and maintenance of the appearance of movement, etc., so the maintenance service will prolong the using time of your watch.

2 watch waterproof

watch waterproof mirror, rear cover, put the table on the first waterproof apron and corresponding to the standard. All waterproof sheets are marked with "RESISTANT WATER" or "PROOF WATER" in English on the bottom cover. No mark can only watch waterproof dustproof, should avoid water. 30 meters (3ATM, 3 ATM) water table, which can be used for daily grooming or rain, splashing on the surface water is only without any pressure on the table. 50 meters waterproof table can be applied to swimming and general housework, 100 meters waterproof table can be used for swimming and diving and other underwater work.

waterproof apron will affect the waterproof performance of the watch, so watch waterproof apron and head (containing rings) changed regularly according to the use to. In order to ensure good waterproof performance, the quartz watch must replace the waterproof element at the same time.

any FangShuiBiao shoulds not be wearing a hot bath, sauna or the great changes in environment temperature in use. Because the waterproof apron will be affected by temperature gap and accelerating aging and cause water table appeared in water and heat bilges cold shrink, serious will make parts damage.

3

watch strap is divided into: Ceramic belt, metal belt (tungsten titanium alloy, copper, steel, solid solid solid powder metallurgy steel, steel belt, steel wire braided belt, braided belt, nylon belt).

ceramic watchband is not easy to wear, not allergic, appearance and other characteristics.

4 watches "two anti"

in the national standard, antimagnetic and shockproof performance standards are "residual effect" represented by the residual effect refers to the instantaneous detection before the instantaneous difference watches and watch the day after the detection of the difference between.

shock: when the watch from a height of 1 meters down to the level of the hardwood surface, the residual effect of quartz table is not more than 2 seconds, the residual effect of the mechanical table is not more than 60 seconds.

: when the watch is accidental magnetic intensity of 4800A/m magnetic field, the effect of residual quartz watch is not more than 1.5 seconds, and mechanical (movement area greater than 314 square mm) residual effect is not more than 30 seconds, word brand mechanical table residual effect of not more than 45 seconds.

5 watch in addition to water MI by

accidentally case in water, can be called a silica particulate matter and have water watch together into a closed container, a few hours later, remove the watch, the water will disappear. This method is simple and economical, the precision and life table without any damage. Has been a number of water after the silica gel, can be dry for several hours at 120 degrees, the water absorption capacity of renewable, but also repeated use.

6 watch refurbished MI by

watch has been marked out a lot of stripes, you can drop one or two drops of water on the table, and then squeeze a little toothpaste rub, you can remove the lines and make the table a new.

7 watches maintenance MI by

(1) wearing a watch, hand sweat is corrosive to the case, the steel case is due to Ni Cr alloy, better anti corrosion performance, a steel case is copper, long-term and sweat contact, easy corrosion, often should use soft cloth to wipe the sweat orpad plastic table support to prevent its being sweat erosion.

(2) do not open the back cover, so as to avoid the dust into the movement of the movement of the normal work of the watch.

(3) don't put the timepiece in mothballs in the wardrobe, in order to avoid the deterioration of the oil table.

(4) do not put the watch on the radio, TV, so as not to magnetization.

(5) for a long time not to wear the watch, should be a regular monthly spring, so that parts will not be in a static state for a long time, in order to ensure the running performance of the table machine.

分享到：